Thin-laying form In the process of laying thin-laying ceramic tiles Home builders รับสร้างบ้าน will use adhesive mortar, epoxy mortar or tile adhesive. Attach the ceramic tile to the wall floor. The wall surface must be smooth and strong and stable before.
- Thin-lay ceramic tile laying requires a wall surface of a certain size, smooth and strong, such as plaster, gypsum board. Gypsum board or plywood
- When building a thin wall in the area exposed to water around the bathtub. Or around the shower can be used as a 12″ (13) thick concrete wall reinforced with fiberglass. (Instead of rebar, which can rust) by using latex mortar or tile adhesive to fix the ceramic tile.
- The surface of the masonry wall should be clean and in good condition. and has a rather rough skin, not slippery to make the latex adhesive mortar good adhesion when laying tiles on the surface.
thick crab
In the process of laying ceramic tiles, sand mortar or cement mortar is applied to the wall surface before the ceramic tile is laid. This method uses mortar. and sand that is thicker than thin crabs Therefore, various plane adjustments can be made. while plastering the wall surface to be vertical and plump
- Wall texture that is suitable for laying thick laying tiles with cement and sand plastered on the wall surface is brick, concrete block, concrete, plywood, gypsum plaster and gypsum board.
- Sand mortar or mortar. It is made up of a mixture of Portland cement, sand, water and sometimes lime. To be plastered on the wall surface to a thickness of ¾” to 1″ (19 to 25).
- Liquid ceramic tile sheets. which is obtained from cement mixed with water To create viscosity under the tile at a thickness of 1⁄16″ (2) before attaching the tile to the damp cement-sand surface. Alternatively, apply a 1⁄8″ to ¼” (3 to 6) thick latex mortar if the cement-sand mortar has hardened.
- Foundation sand mortar 1¼” to 2″ (32 to 51) is poured over the floor before tiling.
- Lay waterproofing sheets to block the cement-sand mortar or mortar so that it is free from causing damage to the floor. and to allow the floor structure below to be able to move freely without holding onto the tiles above.
- In sand mortar or mortar. Steel grating should be reinforced for strength. Whenever a separate waterproofing membrane is laid, the sand mortar is freed from the underlayment.
- Areas suitable for laying thick paving tiles include reinforced concrete floors that have been aged to support the weight and plywood floors that have a firm and strong structure.
- The floor should not have a vertical deflection of more than 1⁄360 of the span length.
- Two floors. It consists of a minimum 5⁄8″ (16) sheet of plywood as a backing. and ½” or 5⁄8″ (13 or 16) outdoor waterproof plywood as a topcoat. By providing a seam between the sheets about ¼” (6) to accommodate the expansion of the plywood sheet. and use epoxy glue to seal the joints
- However, care should be taken that the two-layer wooden floor does not bend vertically by more than 1⁄360.
- Areas suitable for laying thin-walled tiles are concrete floors, two-layer wooden floors.
- Concrete floors should have a smooth, level surface. and reinforce the curing steel until it reaches the age that will support the load Sometimes, prior to tiling, the surface surface may be re-leveled (if desired) with grout in combination with an anti-slip binder.
Details of laying ceramic tiles
Internal wall with thick matting (primed with cement mortar)
- solid wall build houses company บริษัทรับสร้างบ้าน will know that they are made of masonry or metal or wood trusses. Cover the face with a sheet of waterproof material.
- Plastering over steel grates and waterproofing sheets. The plaster has a patterned surface. for adhesion to ceramic tiles
- ¾” to 1″ (19 to 25) thickness mortar, ceramic tile bonded with slurry portland cement or latex adhesive. or mortar
Thin crab form (using a binder)
- Solid and smooth walls. Made of building material or a truss covering the face with a sheet of waterproof material.
- Use a waterproof membrane to be placed over the waterproofing sheet. for wet areas
- Install ceramic tiles with liquid cement. or 1⁄8″ to ¼” (3 to 6) thick latex mortar on the back of the tile.
- Ceramic tiles
Thin Crab (attached with glue)
- Solid and smooth walls. made of building material or a frame covered with a sheet of waterproof material
- Use waterproof gypsum board surface.
- Attach the ceramic tiles with glue thickness 1⁄16″ (2).
interior floor
Thick matting (priming with crab mortar)
- Topcoat with 1¼” to 2″ (32 to 51) mortar or reinforced sand mortar before laying the ceramic tile with adhesive mortar.
- Expansion joints
- waterproofing sheet
- Concrete floor or wooden floor.
Thin crab form (using a binder)
- Install ceramic tiles with liquid cement. or 1⁄8″ to ¼” (3 to 6) thick latex mortar.
behind the tile
- Expansion joints
- concrete floor
Thin Crab (attached with glue)
- Attach the ceramic tile with 1⁄16″ thick adhesive (2).
- If waterproof or chemical is required, epoxy cement should be used.
- Two floors.
shower area
- waterproofing sheet
- Fix the tiles with liquid mortar.
- Sand mortar or steel reinforced mortar poured over the face 1″ to 1¾” (25 to 45) thick.
- Lay waterproofing sheets before pouring mortar on the shower floor.
- The texture of the concrete floor has a sloping surface.
area above the bathtub
- Install the tile with latex glue over the mortar on the panel.
- Waterproof
- Space ¼” (6)
- Flexible waterproof filling material.
- bathtub edge
area on the counter
- Install the tile with glue or latex mortar over the mortar.
- Waterproof
- Install the tile with liquid mortar over the mortar that is ¾” (19) thick.
- Steel grating overlaid with cement mortar.
- Waterproofing sheet over the wooden floor.
